Online decibel meter
See how loud it is around you, with an honest estimate you can calibrate.
- 100% free
- No sign-up
- Runs in your browser
How to use Decibel meter
- Allow the microphone
- Watch the level
- Calibrate if you can
Sound level
–dB
Press Start measuring and allow the microphone.
The last 60 seconds, in estimated dB.
- Min
- —
- Average
- —
- Energy average (Leq)
- Max
- —
How accurate is this?
Browser microphones aren’t calibrated, and phones and laptops shape the sound in their own way. The microphone level in dBFS (decibels below the loudest it can record) is measured exactly; the dB figure is an estimate made by adding the calibration offset to it. It isn’t A-weighted, and a cheap mic can’t hear very quiet rooms or very loud music properly. Use it to compare sounds and spot trends, not for legal or workplace measurements.
Typical sound levels
| Level | Sound |
|---|---|
| 0 dB | Threshold of hearing |
| 10 dB | Quiet breathing |
| 30 dB | Whisper, quiet bedroom at night |
| 40 dB | Quiet library |
| 50 dB | Quiet office, light rain |
| 60 dB | Normal conversation |
| 70 dB | Vacuum cleaner, busy restaurant |
| 85 dB | Heavy city traffic |
| 95 dB | Motorcycle, hand drill |
| 110 dB | Rock concert, nightclub |
| 120 dB | Siren up close, thunder |
| 140 dB | Jet engine at 30 m |
Typical values at a normal listening distance; real sounds vary.
Next: Mic test · Tone generator · Online tuner
Report a problem with this tool
How to use Decibel meter
Allow the microphone
Press Start measuring and allow the microphone. Voice processing is turned off so the raw level is measured.
Watch the level
Read the live level, the minimum, the energy average and the maximum, and follow the last 60 seconds on the chart.
Calibrate if you can
Type what a real sound level meter shows for the same sound and press Match now, so the estimate fits your microphone.
Why use Utils365
Honest numbers
The microphone level in dBFS is exact. The dB figure is clearly marked as an estimate, because browser microphones aren’t calibrated.
Your own calibration
Match one reading to a real meter and the offset is saved on this device, so later readings are much closer.
A proper average
The average is an energy average (Leq), as on real meters, so short loud moments count as much as they should.
Everyday comparisons
A table from a whisper to a jet engine, with the nearest sound highlighted as you measure.
Frequently asked questions
How accurate is a phone or laptop decibel meter?
Without calibration it can be 10 dB or more off, because microphones and their input settings differ; after matching it to a real meter, readings are usually within a few dB, though worse in very quiet rooms or very loud places. Each microphone has its own sensitivity and the browser can’t know it, so treat the dB figure as an estimate.
What is the difference between dBFS and dB SPL?
dBFS is decibels below the loudest sound the microphone can record, so 0 dBFS is the maximum and quieter is negative. dB SPL is the actual sound pressure in the air. Turning one into the other needs a calibration offset.
How do I calibrate the meter?
Play a steady sound, such as pink noise from a speaker, and measure it with a real sound level meter at the same spot. Type that reading and press Match now while measuring. The offset is saved.
How loud is too loud?
Long exposure above 85 dB, like heavy traffic, can damage hearing; workplace rules often limit 85 dB to 8 hours. Each extra 3 dB halves the safe time, so 100 dB is safe for only about 15 minutes.
How many decibels is normal conversation?
About 60 dB at one metre. A whisper is about 30 dB, a quiet library 40 dB, a vacuum cleaner 70 dB and a rock concert around 110 dB.
Is the reading A-weighted?
No. Official noise readings are usually dB(A), which plays down low frequencies as our ears do. This meter weighs all frequencies equally, so rumbly noise can read a few dB higher than an A-weighted meter.
Is anything recorded?
No. The level is measured live in your browser and nothing is recorded or sent. The microphone turns off when you press Stop or leave the page.